Once a natural gas or oil well is drilled, and it has been verified that commercially viable quantities of natural gas are present for extraction, the well must be 'completed' to allow for the flow of petroleum or natural gas out of the formation and up to the surface. This process includes strengthening the well hole with casing, evaluating the pressure and temperature of the formation, and then installing the proper equipment to ensure an efficient flow of natural gas out of the well.
There are two main types of conventional natural gas wells: natural gas wells and natural gas condensate wells. In addition, there are oil wells that contain “associated” natural gas. In an oil well with associated gas, the natural gas is often used to add pressure to the well and enhance the extraction of the well. Sometimes associated natural gas exists in large enough quantities to allow its extraction along with the oil. Natural gas specific wells are wells drilled exclusively for natural gas, and contain little or no oil. Shale-gas drilling is an example of wells being drilled for their natural gas resources.
Condensate wells are wells that contain natural gas, as well as a liquid condensate. This condensate is a liquid hydrocarbon mixture that is often separated from the natural gas either at the wellhead, or during the processing of the natural gas. It is important to remember that natural gas, being lighter than air, will naturally rise to the surface of a well. Because of this, in many natural gas and condensate wells, lifting equipment and well treatment are not necessary.
Completing a well consists of a number of steps: installing the well casing, completing the well, installing the wellhead, and installing lifting equipment or treating the formation should that be required. Click on the links below to learn about these aspects of the well completion process:
Well Casing
Installing well casing is an important part of the drilling and completion process. Well casing consists of a series of metal tubes installed in the freshly drilled hole. Casing strengthens the sides of the well hole, ensures that no oil or natural gas seeps out of the well hole as it is brought to the surface, and keeps other fluids or gases from seeping into the formation through the well. A good deal of planning is necessary to ensure that the proper casing for each well is installed. The type of casing used depends on the subsurface characteristics of the well, including the diameter of the well and the pressures and temperatures experienced throughout the well. The diameter of the well hole depends on the size of the drill bit used. In most wells, the diameter of the well hole decreases the deeper it is drilled, leading to a type of conical shape that must be taken into account when installing casing. To review the drilling of a natural gas well and the history of drilling practices, including casing, click here.
There are five different types of well casing. They include:
- Conductor Casing
- Surface Casing
- Intermediate Casing
- Liner String
- Production Casing
Conductor Casing
Conductor casing is installed first, usually prior to the arrival of the drilling rig. The hole for conductor casing is often drilled with a small auger drill, mounted on the back of a truck. Conductor casing is usually no more than 20 to 50 feet long. It is installed to prevent the top of the well from caving in and to help in the process of circulating the drilling fluid up from the bottom of the well. Onshore, this casing is usually 16 to 20 inches in diameter, while offshore casing usually measures 30 to 42 inches. The conductor casing is cemented into place before drilling begins.
Surface casing is the next type of casing to be installed. It can be anywhere from a few hundred to 2,000 feet long, and is smaller in diameter than the conductor casing. When installed, the surface casing fits inside the top of the conductor casing. The primary purpose of surface casing is to protect fresh water deposits near the surface of the well from being contaminated by leaking hydrocarbons or salt water from deeper underground. It also serves as a conduit for drilling mud returning to the surface, and helps protect the drill hole from being damaged during drilling. Surface casing, like conductor casing, is cemented into place. Regulations often dictate the thickness of the cement to be used to ensure that there is little possibility of freshwater contamination.
Intermediate Casing
Intermediate casing is usually the longest section of casing found in a well. The primary purpose of intermediate casing is to minimize the hazards that come along with subsurface formations that may affect the well. These include abnormal underground pressure zones, underground shale, and formations that might otherwise contaminate the well, such as underground salt-water deposits. In many instances, even though there may be no evidence of an unusual underground formation, intermediate casing is run as insurance against the possibility of such a formation affecting the well. These intermediate casing areas may also be cemented into place for added protection.
Liner Strings
Liner strings are sometimes used instead of intermediate casing. Liner strings are commonly run from the bottom of another type of casing to the open well area. However, liner strings are usually attached to the previous casing with 'hangers', instead of being cemented into place. This type of casing is thus less permanent than intermediate casing.
Production Casing
Production casing, alternatively called the 'oil string' or 'long string,’ is installed last and is the deepest section of casing in a well. This is the casing that provides a conduit from the surface of the well to the petroleum-producing formation. The size of the production casing depends on a number of considerations, including the lifting equipment to be used, the number of completions required, and the possibility of deepening the well at a later time. For example, if it is expected that the well will be deepened at a later date, then the production casing must be wide enough to allow the passage of a drill bit later on.
Well casing is a very important part of the completed well. In addition to strengthening the well hole, it provides a conduit to allow hydrocarbons to be extracted without intermingling with other fluids and formations found underground. It is also instrumental in preventing blowouts, allowing the formation to be 'sealed' from the top should dangerous pressure levels be reached. For more technical information on blowouts and their prevention, click . Once the casing has been set, and in most cases cemented into place, proper lifting equipment is installed to bring the hydrocarbons from the formation to the surface. After the casing is installed, tubing is inserted inside the casing, running from the opening well at the top to the formation at the bottom. The hydrocarbons that are extracted go up this tubing to the surface. This tubing may also be attached to pumping systems for more efficient extraction, should that be necessary.
Completion
Well completion commonly refers to the process of finishing a well so that it is ready to produce oil or natural gas. In essence, completion consists of deciding on the characteristics of the intake portion of the well in the targeted hydrocarbon formation. There are a number of types of completions, including:
- Open Hole Completion
- Conventional Perforated Completion
- Sand Exclusion Completion
- Permanent Completion
- Multiple Zone Completion
- Drainhole Completion
The use of any type of completion depends on the characteristics and location of the hydrocarbon formation to be mined.
Open Hole Completion
Open hole completions are the most basic type and are used in formations that are unlikely to cave in. An open hole completion consists of simply running the casing directly down into the formation, leaving the end of the piping open without any other protective filter. Very often, this type of completion is used on formations that have been ‘acidized’ or ‘fractured.’
Conventional Perforated Completion
Conventional perforated completions consist of production casing being run through the formation. The sides of this casing are perforated, with tiny holes along the sides facing the formation, which allows for the flow of hydrocarbons into the well hole, but still provides a suitable amount of support and protection for the well hole. The process of perforating the casing involves the use of specialized equipment designed to make tiny holes through the casing, cementing, and any other barrier between the formation and the open well. In the past, 'bullet perforators' were used, which were essentially small guns lowered into the well. The guns, when fired from the surface, sent off small bullets that penetrated the casing and cement. Today, 'jet perforating' is preferred. This consists of small, electrically-ignited charges, lowered into the well. When ignited, these charges poke tiny holes through to the formation, in the same manner as bullet perforating.
Sand Exclusion Completion
Sand exclusion completions are designed for production in an area that contains a large amount of loose sand. These completions are designed to allow for the flow of natural gas and oil into the well, but at the same time prevent sand from entering the well. Sand inside the well hole can cause many complications, including erosion of casing and other equipment. The most common methods of keeping sand out of the well hole are screening or filtering systems. These include analyzing the sand experienced in the formation and installing a screen or filter to keep sand particles out. The filter may be either a type of screen hung inside the casing, or a layer of specially-sized gravel outside the casing to filter out the sand. Both types of sand barriers can be used in open holes and perforated completions.
Permanent Completion
Permanent completions are those in which the components are assembled and installed only once. Installing the casing, cementing, perforating, and other completion work is done with small diameter tools to ensure the permanent nature of the completion. Completing a well in this manner can lead to significant cost savings compared to other types.
Multiple Zone Completion
Multiple zone completion is the practice of completing a well so that hydrocarbons from two or more formations may be produced simultaneously, yet separately. For example, a well may be drilled that passes through a number of formations as it descends; alternately, it may be more effective in a horizontal well to add multiple completions to drain the formation efficiently. Although it is common to separate multiple completions so that the fluids from the different formations do not intermingle, the complexity of achieving complete separation can present a barrier. In some instances, the different formations being drilled are close enough to allow fluids to intermingle in the well hole. When it is necessary to prevent this intermingling, hard rubber 'packing' instruments are used to maintain separation among different completions.
Drainhole Completion
Drainhole completions are a form of horizontal or slant drilling. This type of completion consists of drilling out horizontally into the formation from a vertical well, providing a 'drain' for the hydrocarbons to empty into the well. In certain formations, drilling a drainhole completion may allow for more efficient and balanced extraction of the targeted hydrocarbons. Drainhole completions are more commonly associated with oil wells than with natural gas wells.
The Wellhead
The wellhead consists of the pieces of equipment mounted at the opening of the well to manage the extraction of hydrocarbons from the underground formation. It prevents leaking of oil or natural gas out of the well, and also prevents blowouts caused by high pressure. Formations that are under high pressure typically require wellheads that can withstand a great deal of upward pressure from the escaping gases and liquids. These wellheads must be able to withstand pressures of up to 20,000 pounds per square inch (psi). The wellhead consists of three components: the casing head, the tubing head, and the 'christmas tree.’
The casing head consists of heavy fittings that provide a seal between the casing and the surface. The casing head also serves to support the entire length of casing that is run all the way down the well. This piece of equipment typically contains a gripping mechanism that ensures a tight seal between the head and the casing itself.
The tubing head is much like the casing head. It provides a seal between the tubing, which is run inside the casing, and the surface. Like the casing head, the tubing head is designed to support the entire length of the casing, as well as provide connections at the surface, which allow the flow of fluids out of the well to be controlled.
The 'christmas tree' is the piece of equipment that fits on top of the casing and tubing heads, and contains tubes and valves that control the flow of hydrocarbons and other fluids out of the well. It commonly contains many branches and is shaped somewhat like a tree, thus its name, ‘christmas tree.’ The christmas tree is the most visible part of a producing well, and allows for the surface monitoring and regulation of the production of hydrocarbons from a producing well. A typical Christmas tree is about six feet tall.
Lifting and Well Treatment
Once the well is completed, it may begin to produce natural gas. In some instances, the hydrocarbons that exist in pressurized formations will naturally rise up through the well to the surface. This is most commonly the case with natural gas. Since natural gas is lighter than air, once a path to the surface is opened, the pressurized gas will rise to the surface with little or no interference. This is most common for formations containing natural gas alone, or with only a light condensate. In these scenarios, once the christmas tree is installed, the natural gas will flow to the surface without assistance.
In order to more fully understand the nature of the well, a potential test is typically run in the early days of production. This test allows well engineers to determine the maximum amount of natural gas that the well can produce in a 24-hour period. From this and other knowledge of the formation, the engineer may make an estimation on what the 'most efficient recovery rate', or MER will be. The MER is the rate at which the greatest amount of natural gas may be extracted without harming the formation itself.
Another important aspect of producing wells is the 'decline rate'. When a well is first drilled, the formation is under pressure and produces natural gas at a very high rate. However, as more and more natural gas is extracted from the formation, the production rate of the well decreases. This is known as the decline rate. Certain techniques, including lifting and well stimulation, can increase the production rate of a well.
In some natural gas wells, and oil wells that have associated natural gas, it is more difficult to ensure an efficient flow of hydrocarbons up the well. The underground formation may be very 'tight', making the movement of petroleum through the formation and up the well a very slow and inefficient process. In these cases, lifting equipment or well treatment is required.
Lifting equipment consists of a variety of specialized equipment used to help 'lift' petroleum out of a formation. This is most commonly used to extract oil from a formation. Because oil is found as a viscous liquid, it takes some coaxing to extract it from underground. Various types of lifting equipment are available, but the most common lifting method is known as 'rod pumping'. Rod pumping is powered by a surface pump that moves a cable and rod up and down in the well, providing the lifting pressure required to bring the oil to the surface. The most common type of cable rod lifting equipment is the 'horse head' or conventional beam pump. These pumps are recognizable by the distinctive shape of the cable feeding fixture, which resembles a horse's head.
Well Treatment
Well treatment is another method of ensuring the efficient flow of hydrocarbons out of a formation. Essentially, this type of well stimulation consists of injecting acid, water, or gases into the well to open up the formation and allow the petroleum to flow through the formation more easily. Acidizing a well consists of injecting acid (usually hydrochloric acid) into the well. In limestone or carbonate formations, the acid dissolves portions of the rock in the formation, opening up existing spaces to allow for the flow of petroleum. Fracturing consists of injecting a fluid into the well, the pressure of which 'cracks' or opens up fractures already present in the formation. In addition to the fluid being injected, 'propping agents' are also used. These propping agents can consist of sand, glass beads, epoxy, or silica sand, and serve to prop open the newly widened fissures in the formation. Hydraulic fracturing involves the injection of water into the formation, while CO2 fracturing uses gaseous carbon dioxide. Fracturing, acidizing, and lifting equipment may all be used on the same well to increase permeability, widening the pores of the formation.
These techniques have been more common to oil wells, but are increasingly being applied to increase the extraction rate for gas wells, particularly hydraulic fracturing. As deeper and less conventional natural gas wells are drilled, it is becoming more common to use stimulation techniques on gas wells.
Click on the following links to learn more: and shale gas.
The next step in the process of producing natural gas is processing. This involves taking the 'raw' natural gas obtained from underground, removing impurities, and ensuring that the gas is ready for use prior to being transported to its destination.
.jpg)
